考虑加速度约束的终端角度约束滑模制导律设计
作者:
作者单位:

1. 上海交通大学 自动化系,上海 200240;2. 上海交通大学 系统控制与信息处理教育部 重点实验室,上海 200240;3. 上海交通大学 海洋智能装备与系统集成技术教育部实验室, 上海 200240;4. 中国空空导弹研究院,河南 洛阳 471000

作者简介:

通讯作者:

E-mail: yzcai@sjtu.edu.cn.

中图分类号:

V448.13

基金项目:

国家自然科学基金重大科研仪器研制项目(61627810);国家科技重大专项项目(2018YFB1305003).


Sliding-mode guidance law with acceleration and angle constraints
Author:
Affiliation:

1. Department of Automation,Shanghai Jiao Tong University,Shanghai 200240,China;2. Key Laboratory of System Control and Information Processing of Ministry of Education,Shanghai Jiao Tong University, Shanghai 200240,China;3. Key Laboratory of Marine Intelligent Equipment and System of Ministry of Education,Shanghai Jiao Tong University,Shanghai 200240,China;4. China Air-borne Missile Academy,Luoyang 471000,China

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对含终端角度约束的滑模制导律在制导初期加速度指令过大的问题,采用趋近律方法和引入阻尼项设计一种考虑加速度约束的角度约束滑模制导律.首先,分析制导指令大小与滑模变量趋近速度的关系;然后,在滑模面函数中引入阻尼项,动态调节制导指令中不同部分的占比,从而降低制导初期整体指令值;最后,设计多幂次自适应趋近律来调节不同阶段的滑模变量趋近速度,达到降低制导指令极值、满足加速度约束的目的,同时保证滑模面函数的快速收敛.与常见的终端角度约束滑模制导律相比,仿真结果验证了所提出方法在降低加速度极值方面的有效性.

    Abstract:

    Concerning the problem that the sliding mode guidance law with terminal angle constraint has too large an acceleration command at the initial stage of guidance process, an angle constraint guidance law considering acceleration constraint is designed using the reaching law method and a damping term. The relationship between the magnitude of the acceleration command and the approaching speed of the sliding mode variable is analyzed first. Then, a damping term is introduced into the sliding mode surface function to dynamically adjust the proportion of different parts of the guidance instruction, thereby reducing the overall instruction value at the initial stage of the guidance process. Finally, a multi-power adaptive reaching law is designed to adjust the approaching speed of the sliding mode variable at different stages to reduce the extreme value of the guidance instruction and meet the acceleration constraint. The fast convergence of the sliding mode surface function is guaranteed in the meantime. Compared with the common terminal-angle-constrained sliding mode control-based guidance law, the simulation results demonstrate the effectiveness of the proposed guidance law in reducing acceleration command extremes.

    参考文献
    相似文献
    引证文献
引用本文

李泽仁,崔颢,章露露,等.考虑加速度约束的终端角度约束滑模制导律设计[J].控制与决策,2021,36(10):2511-2516

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2021-08-18
  • 出版日期: 2020-10-20